IEEE Transactions on Power Electronics. Sep2019, Vol. 34 Issue 9, p8715-8723. 9p.
RAPID prototyping, CURRENT-voltage characteristics, and FEEDBACK (Psychology)
Using a photovoltaic (PV) emulator (PVE) simplifies the testing of the PV generation system. However, conventional controllers used for PVEs suffer from oscillating output voltage, requiring a high number of iterations, or being too complex to be implemented. This paper proposes a controller based on a resistance feedback control strategy that produces a stable and fast converging operating point for the PVE. The resistance feedback control strategy requires a new type of PV model, which is the current–resistance (I–R) PV model. This model is computed using a binary search method at a fast convergence rate. It is combined with a closed-loop buck converter using a proportional-integral controller to form the resistance feedback control strategy. The PVE's controller is implemented into dSPACE ds1104 hardware platform for experimental validation. The acquired experimental results show that the proposed PVE is able to follow the current–voltage characteristic of the PV module accurately. In addition, the PVE's efficiency is more than 90% under maximum power point operation. The transient response of the proposed PVE is similar to the PV panel during irradiance changes. [ABSTRACT FROM AUTHOR]
This paper presents a discrete-time neural inverse optimal control for induction motors, which is implemented on a rapid control prototyping (RCP) system using a C2000 Microcontroller-Simulink platform. Such controller addresses the solution of three issues: system identification, trajectory tracking, and state estimation, which are solved independently. The neural controller is based on a recurrent high order neural network (RHONN), which is trained with an extended Kalman filter. The RHONN is an identifier to obtain an accurate motor model, which is robust to external disturbances and parameter variations. The inverse optimal controller is used to force the system to track a desired trajectory and to reject undesired disturbances. Moreover, the controller is based on a neural model and does not need the a-priori knowledge of motor parameters. A supertwisting observer is implemented to estimate the rotor magnetic fluxes. The hub of the RCP system is a TMS320f28069M MCU, which is an embedded combination of a 32-bit C28x DSP core and a real-time control accelerator. This Microcontroller is fully programmable from the Simulink environment. Simulation and experimental results illustrate the performance of the proposed controller and the RCP system, and a comparison with a control algorithm without the neural identifier is also included. [ABSTRACT FROM AUTHOR]
TARGET costing, PROTOTYPES, PRODUCT design, RAPID prototyping, and SUPPLIERS
Prototyping allows firms to evaluate the technical feasibility of alternative product designs and to better estimate their costs. We study a collaborative prototyping scenario in which a manufacturer involves a supplier in the prototyping process by letting the supplier make detailed design choices for critical components and provide prototypes for testing. While the supplier can obtain private information about the costs, the manufacturer uses target costing to gain control over the design choice. We show that involving the supplier in the prototyping process has an important influence on the manufacturer's optimal decisions. The collaboration results in information asymmetry, which makes parallel prototyping less attractive and potentially reverses the optimal testing sequence under sequential prototyping: It may be optimal to test designs in increasing order of attractiveness to avoid that the supplier does not release technically and economically feasible prototypes for strategic reasons. We also find that the classical target costing approaches (cost‐ and market‐based) need to be adjusted in the presence of alternative designs: Due to the strategic behavior of suppliers, it is not always optimal to provide identical target costs for designs with similar cost and performance estimates, nor to provide different target costs for dissimilar designs. Furthermore, the timing is important: While committing upfront to carefully chosen target costs reduces the supplier's strategic behavior, in some circumstances, the manufacturer can take advantage of this behavior by remaining flexible and specifying the second prototype's target costs later. [ABSTRACT FROM AUTHOR]
Bryden, Douglas (Designer), author. and Bryden, Douglas (Designer), author.
Industrial design -- Computer-aided design -- Case studies., Product design -- Computer-aided design -- Case studies., Computer-aided design., Rapid prototyping., Industrial design -- Data processing -- Case studies., Industrial design -- Data processing., and Case studies.
Computer-aided design (CAD) and rapid prototyping (RP) are now a fundamental part of the professional practice of product design and are therefore essential skills for product design undergraduate students. This book provides students with all the tools needed to get to grips with the range of both CAD software and RP processes used in the industry.
RAPID prototyping, SEARCH algorithms, DIELECTRIC-loaded antennas, THREE-dimensional printing, and PERMITTIVITY
A prototyping method for dielectrically loaded antennas is presented. Dielectric loading has been used with horn antennas, feeds, and lenses. Dielectrics have also been used for coating antennas submerged in water and biological matter and have led to improvements in bandwidth and efficiency as well as antenna miniaturisation. The authors present a new technique to produce variable dielectrics with permittivity from 6 to 28 using two commonly available powders, titanium dioxide (used in foods) and magnesium silicate (used in talcum powder). An example spherical helical ball antenna is used to demonstrate the process. In this antenna, the mixed powders were encased in a 3D printed shell that achieved a reduction in diameter of the spherical antenna by a factor of 1.85. The technique aids rapid prototyping and optimisation using search algorithms. [ABSTRACT FROM AUTHOR]
As relationship marketing research evolved, a number of key constructs emerged. Some scholars have argued that these constructs are not conceptually or empirically distinct. We investigate this phenomenon based on the premise that sustained research effort towards studying conceptually overlapping/redundant constructs, while treating them as independent, can hamper the development of the field. We use prototyping, a method adopted from psychology, to examine consumers’ views of these constructs, and then identify relationship contexts where constructs are distinct or redundant. [ABSTRACT FROM AUTHOR]
Haller, Norm, author. and National Research Council (U.S.). Air Force Studies Board, issuing body.
Prototypes, Engineering -- Congresses., Rapid prototyping -- Congresses., and Military research -- United States -- Planning -- Congresses.
"Assessment to Enhance Air Force and Department of Defense Prototyping for the New Defense Strategy is the summary of a workshop convened by the Air Force Studies Board of the National Academies' National Research Council in September 2013 to enhance Air Force and Department of Defense (DoD) prototyping for the new defense strategy. This workshop examined of a wide range of prototyping issues, including individual recommendations for a renewed prototype program, application of prototyping as a tool for technology/system development and sustainment (including annual funding), and positive and negative effects of a renewed program. Prototyping has historically been of great benefit to the Air Force and DoD in terms of risk reduction and concept demonstration prior to system development, advancing new technologies, workforce enhancement and skills continuity between major acquisitions, dissuasion of adversaries by demonstrating capabilities, maintaining technological surprise through classified technologies, and an overarching strategy of overall risk reduction during austere budget environments. Over the last two decades, however, many issues with prototyping have arisen. For example, the definitions and terminology associated with prototyping have been convoluted and budgets for prototyping have been used as offsets to remedy budget shortfalls. Additionally, prototyping has been done with no strategic intent or context, and both government and industry have misused prototyping as a key tool in the DoD and defense industrial base. Assessment to Enhance Air Force and Department of Defense Prototyping for the New Defense Strategy envisions a prototyping program that encourages innovation in new concepts and approaches and provides a means to assess and reduce risk before commitment to major new programs."--Publisher's description.