Polo-Lopez, Lucas, Masa-Campos, Jose L., and Ruiz-Cruz, Jorge A.
International Journal of RF and Microwave Computer-Aided Engineering. Dec 2019, Vol. 29 Issue 12, n/a
Satellite communications, Antennas (Electronics) -- Design and construction, Waveguides -- Design and construction, Sintering, 3D printing, and Computer-aided design
Keywords: additive manufacturing; fused filament fabrication; phase shifter; reconfigurable; selective laser sintering; waveguide Abstract This work presents the design and manufacturing of a K-band reconfigurable phase shifter completely implemented in waveguide technology for reduced insertion loss, good matching, and large phase shifting range. The device is based on the combination of a short slot coupler and two tunable reactive loads implemented as a section of short-circuited waveguide where an adjustable metallic post is inserted. Three prototypes of this design have been manufactured using different techniques (conventional computer numerical control machining, a low-cost fused filament fabrication technique and direct metal laser sintering) in order to assess its performance for different applications. The prototypes have been characterized experimentally and the achieved results are evaluated and compared. The proposed phase shifter, since it is fully developed in waveguide technology, eliminates the need of adding transitions to planar structures in order to integrate lumped components like pin diodes or varactors. Therefore, this device has a great potential in high-power beam steering phased arrays. Biographical information: Lucas Polo-Lopez received the BSc and MSc degrees in Telecommunication Engineering from the Universidad Autonoma de Madrid, Madrid, Spain in 2014 and 2016, respectively. Since 2015 he has been with the Radiofrequency Circuits, Antennas and Systems (RFCAS) group of this same university, where he works toward the PhD degree. His current research interests include the computer-aided design of horn antennas and passive waveguide devices, as well as the application of additive manufacturing techniques to the construction of waveguide devices. Jose L. Masa-Campos received the Master degree in 1999 and the PhD Degree in 2006, from the Universidad Politecnica de Madrid, Spain. From 1999 to 2003 he developed his professional activity in the R&D department of the company RYMSA with the design of base station antennas for mobile communications and satellite antennas. From 2002 to 2003 he directed the R&D department of RYMSA. From 2003 to 2007, he worked as Researcher for Universidad Politecnica de Madrid, and in 2005 he joined to Universidad Autonoma de Madrid as Associate Professor in the Radiofrequency Circuits, Antennas and Systems (RFCAS) group. His main current research interests are in active and passive planar array antennas. Jorge A. Ruiz-Cruz received the Ingeniero de Telecomunicacion degree and the PhD degree from the Universidad Politecnica de Madrid, Madrid, Spain, in 1999 and 2005, respectively. Since 2006, he has been with the Universidad Autonoma de Madrid, Madrid, where he became an Associate Professor in 2009. His current research interests include the computer-aided design of microwave passive devices and circuits (filters, multiplexers, and orthomodes). Byline: Lucas Polo-Lopez,Jose L. Masa-Campos,Jorge A. Ruiz-Cruz
Bryden, Douglas (Designer), author. and Bryden, Douglas (Designer), author.
Industrial design -- Computer-aided design -- Case studies., Product design -- Computer-aided design -- Case studies., Computer-aided design., Rapid prototyping., Industrial design -- Data processing -- Case studies., Industrial design -- Data processing., and Case studies.
Computer-aided design (CAD) and rapid prototyping (RP) are now a fundamental part of the professional practice of product design and are therefore essential skills for product design undergraduate students. This book provides students with all the tools needed to get to grips with the range of both CAD software and RP processes used in the industry.
Byline: Mohamed Farid Shehab, Nabila Mohammed Abdel Hamid, Nevien Abdullatif Askar, Ahmed Mokhtar Elmardenly Keywords: CAD-CAM, electron beam melting; immediate mandibular reconstruction; patient-specific titanium mesh; rapid prototyping Abstract Background Immediate mandibular reconstruction was performed using a patient-specific titanium mesh tray fabricated by electron beam melting (EBM) /rapid prototyping techniques. Methods Patient-specific titanium trays were virtually designed and fabricated using EBM technology/rapid prototyping for patients requiring mandibular resection and immediate reconstruction using an iliac crest bone graft. Dental implants were placed in the grafted sites and the patients received prosthetic rehabilitation with a follow-up of one year. Clinical data, postoperative bone formation and complications were evaluated. Results A symmetric appearance of facial contours was achieved. The titanium tray incorporated the particulate iliac crest bone graft that provided significant bone formation (mean 18.97 [+ or -] 1.45 mm) and predictable results. Stability of the dental implants was achieved. Conclusion The patient-specific titanium meshes and immediate particulate autogenous bone graft showed satisfactory clinical and surgical results in improving patients' quality of life and decreasing the overall treatment time with adequate functional rehabilitation.
Haller, Norm, author. and National Research Council (U.S.). Air Force Studies Board, issuing body.
Prototypes, Engineering -- Congresses., Rapid prototyping -- Congresses., and Military research -- United States -- Planning -- Congresses.
"Assessment to Enhance Air Force and Department of Defense Prototyping for the New Defense Strategy is the summary of a workshop convened by the Air Force Studies Board of the National Academies' National Research Council in September 2013 to enhance Air Force and Department of Defense (DoD) prototyping for the new defense strategy. This workshop examined of a wide range of prototyping issues, including individual recommendations for a renewed prototype program, application of prototyping as a tool for technology/system development and sustainment (including annual funding), and positive and negative effects of a renewed program. Prototyping has historically been of great benefit to the Air Force and DoD in terms of risk reduction and concept demonstration prior to system development, advancing new technologies, workforce enhancement and skills continuity between major acquisitions, dissuasion of adversaries by demonstrating capabilities, maintaining technological surprise through classified technologies, and an overarching strategy of overall risk reduction during austere budget environments. Over the last two decades, however, many issues with prototyping have arisen. For example, the definitions and terminology associated with prototyping have been convoluted and budgets for prototyping have been used as offsets to remedy budget shortfalls. Additionally, prototyping has been done with no strategic intent or context, and both government and industry have misused prototyping as a key tool in the DoD and defense industrial base. Assessment to Enhance Air Force and Department of Defense Prototyping for the New Defense Strategy envisions a prototyping program that encourages innovation in new concepts and approaches and provides a means to assess and reduce risk before commitment to major new programs."--Publisher's description.
Gibson, I. (Ian), Rosen, D. W. (David W.), Stucker, B. (Brent), and Gibson, I. (Ian)
Manufacturing processes -- Automation., Production control -- Automation., CAD/CAM systems., and Rapid Prototyping (Fertigung)
"Additive Manufacturing Technologies: Rapid Prototyping to Direct Digital Manufacturing deals with various aspects of joining materials to form parts. Additive Manufacturing (AM) is an automated technique for direct conversion of 3D CAD data into physical objects using a variety of approaches. Manufacturers have been using these technologies in order to reduce development cycle times and get their products to the market quicker, more cost effectively, and with added value due to the incorporation of customizable features. Realizing the potential of AM applications, a large number of processes have been developed allowing the use of various materials ranging from plastics to metals for product development. Authors Ian Gibson, David W. Rosen and Brent Stucker explain these issues, as well as: Providing a comprehensive overview of AM technologies plus descriptions of support technologies like software systems and post-processing approaches ; Discussing the wide variety of new and emerging applications like micro-scale AM, medical applications, direct write electronics and Direct Digital Manufacturing of end-use components ; Introducing systematic solutions for process selection and design for AM. Additive Manufacturing Technologies: Rapid Prototyping to Direct Digital Manufacturing is the perfect book for researchers, students, practicing engineers, entrepreneurs, and manufacturing industry professionals interested in additive manufacturing."--Publisher's website.
Dorozynski, Przemyslaw, Jamroz, Witold, Wegiarz, Wladyslaw P., Kulinowski, Wojciech, Zaborowski, Mateusz, and Kulinowski, Piotr
Dissolution Technologies. Nov 2018, Vol. 25 Issue 4, p48, 6 p.
3D printing and Testing equipment
INTRODUCTION The number of studies concerning application of three dimensional (3D) printing techniques in pharmaceutical technology has grown continuously since 2005, but the main interest in application of these techniques [...] Purpose of the research was to assess feasibility of fused deposition techniques (3D printing) for development of analytical equipment dedicated for specific dosage forms and for nonstandard applications. Dissolution profiles as well as 3D magnetic resonance imaging (MRI) of the buccal tablets during hydration in dissolution medium were analyzed. The principal result of the study was the first working example of rapid 3D prototyping of dedicated, MRI-compatible dissolution equipment for mucoadhesive buccal tablets. Rapid prototyping techniques were found to be a fast, inexpensive way to develop a dedicated dissolution testing setup. KEYWORDS: additive manufacturing, 3D printing, solid free-form fabrication, buccal bioadhesive tablets, 3D ultrashort echo time magnetic resonance imaging (3D UTE MRI), pharmaceutical dissolution testing equipment